Ingredient

Creatine mesh size explained: what 500 mesh means for your formula

What 500 mesh means in microns, what an ultrafine creatine powder changes in a drink, what it does not change, and serving maths for formulators.

By CreaPro®4 min read

Hand gripping a loaded barbell in a gym
On this page
  1. What a mesh number measures
  2. What a finer powder changes
  3. What it does not change
  4. Serving maths for formulators
  5. Handling an ultrafine powder
  6. Key points
  7. Sources

Two creatine monohydrate powders can share the same purity and still behave very differently in a shaker, a stick pack or a filling line. The difference is particle size, which a technical data sheet usually gives as a mesh number. CreaPro® is specified at Mesh 500, one of the finest grades of creatine monohydrate. This article explains what that number means, what a finer powder changes, and what it does not.

What a mesh number measures

A mesh number counts the openings per linear inch of a test sieve. The higher the number, the smaller each opening, so a higher mesh means a finer powder. A powder described as 500 mesh passes a sieve with openings of about 25 µm (micrometers, or thousandths of a millimeter).

MeshSieve openingHow the grade is usually described
80 meshabout 180 µmStandard, granular
200 meshabout 75 µmMicronized
500 meshabout 25 µmUltra-micronized, such as CreaPro®
Sieve openings are approximate. The US standard (ASTM E11) and the older Tyler scale differ slightly, for example 75 µm against 74 µm at 200 mesh.

Put simply, a 500 mesh opening is about a third of the width of a 200 mesh opening.

What a finer powder changes

It wets and disperses faster

Surface area per gram rises as particle size falls. For particles of a similar shape, a third of the size means roughly three times the surface area per gram, so water reaches more of the powder at once. An ultrafine powder wets out and disperses quickly instead of floating as dry clumps or sinking as grit.

It feels smoother

Large crystals are what consumers notice as sand at the bottom of a shaker or grit on the tongue. A finer powder leaves fewer particles large enough to feel. That matters most in clear drinks and unflavored products, where nothing hides the texture.

It stays suspended longer

For small particles in water, settling speed rises with the square of the particle diameter (Stokes’ law). A particle a third of the size settles about nine times more slowly, so creatine that has not yet dissolved stays spread through the drink rather than collecting at the bottom.

What it does not change

Mesh size changes how fast creatine dissolves, not how much can dissolve. Creatine monohydrate dissolves at about 14 g per liter of water at 20 °C, and its solubility rises almost linearly with temperature (Jäger et al., 2011). A finer powder reaches that limit sooner. It does not raise it.

Mesh size is not about absorption either. Creatine monohydrate is already almost completely absorbed from the gut, as covered on our Creatine Knowledge page. Choosing a finer grade is a decision about mixing, texture and the look of the drink.

Serving maths for formulators

Two figures on a data sheet answer most practical questions. Solubility sets how much water a serving needs to dissolve fully, and bulk density sets how much room a serving takes in a scoop or stick pack. CreaPro® has a bulk density of approximately 581 g/l.

ServingWater to dissolve fully at 20 °CLoose powder volume at 581 g/l
3 gabout 215 mlabout 5.2 ml
5 gabout 360 mlabout 8.6 ml
Calculated from a solubility of 14 g/l at 20 °C and the CreaPro® bulk density. Warmer water dissolves more.

Above those ratios the extra creatine is suspended rather than dissolved, which is where the slow settling of a fine powder helps. Bulk density is measured on loose powder, and powder settles and packs denser in transport and filling, so confirm scoop and fill volumes in your own trials.

Handling an ultrafine powder

A finer grade asks a little more of a production floor. A creatine purification patent notes that a coarser product forms less dust and has a reduced tendency toward electrostatic charging and caking (US Patent 6,399,819). In practice:

  • Expect more dust than with a granular grade, and use dust extraction where powder is tipped and blended.
  • Fine powders flow less freely than coarse ones. Check flow on your own filling line before you scale up.
  • Keep it dry. Moisture makes a fine powder cake, and caked powder loses the fast mixing you chose it for. Our article on storage and shelf life covers the details.
  • When blending with much coarser ingredients, check that the blend does not separate in transport. Particles of very different sizes can segregate.

Key points

  • Mesh counts sieve openings per inch: 500 mesh is about 25 µm, roughly a third of 200 mesh.
  • A finer powder disperses faster, feels smoother and settles more slowly.
  • It does not raise solubility (about 14 g/l at 20 °C), and it is not about absorption.
  • At 581 g/l, a 5 g serving of CreaPro® takes about 8.6 ml of loose powder.

Sources

  1. Jäger R, Purpura M, Shao A, Inoue T, Kreider RB. Analysis of the efficacy, safety, and regulatory status of novel forms of creatine. Amino Acids. 2011;40(5):1369–1383. PMC3080578
  2. US Patent 6,399,819, Process for purifying creatine. Google Patents
  3. ASTM E11, Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves.
  4. CreaPro® technical data sheet, edition Sep-26. Download the PDF
Share this article LinkedIn Email
All articles
Keep reading

More articles.

All articles